Carte de développement RV1109 carte de base RV1109 puce rock IPC
- Type d'accessoire: Carte d'extension
- NPU: 1.2 TOPS NPU
- système: Linux 4.19 QT 5.12
- Mémoire: 1GB
- stockage: 8GB
Taille | 44mmL*44mmW*3.2mmH |
CPU | Puce suisse RV1109 fréquence double cœur 1200 MHz |
NPU | 1.2 TOPS NPU |
Mémoire | DDR4 standard 1 Go 2 Go en option |
Mémoire | MEM 5.1 Standard 8 Go 16 Go/32G/64G/128G en option |
gestion de l'alimentation | RK809-2 prend en charge la gestion dynamique de l'alimentation |
Tension de fonctionnement | Tension d'entrée 5V, puissance maximale inférieure à 2W (Ne connectez aucun périphérique) |
système de support | Linux 4.19 + QT 5.12 |
température de fonctionnement | -10à +60 degrés |
la vie | La durée de vie continue est supérieure à 5 ans |
interface USB | USB bidirectionnel,OTG indépendant jusqu'au bout,HÔTE indépendant jusqu'au bout |
Port série UART | 6Niveau TTL 3.3V,Une façon est le débogage |
Interface GPIO | 98GPIO(Remarque:A une fonction de multiplexage,Veuillez vérifier la définition de la broche dans cette spécification) |
Interface PWM | 12Le canal PWM a un niveau de 3,3 V/1,8 V respectivement(Veuillez vérifier la définition de la broche dans cette spécification) |
Affichage MIPI DSI | 1路最大1920×1080 60fps |
Affichage RVB | 1Interface d'affichage RVB 888,最大1920×1080 |
Interface caméra DVP | 1Interface de caméra DVP parallèle 16 bits |
Interface caméra MIPI | 2Canal Données MIPI CSI RAW Interface caméra |
sortie vocale | 1Sortie des canaux gauche et droit,Amplificateur de puissance 10 W fixé à la plaque inférieure |
Entrée vocale | 1Entrée microphone numérique PDM en silicone,1Entrée analogique de canal LANE_IN |
Interface SDIO | 2Interface SDIO,Tout le chemin carte TF,Une autre façon de se connecter au WIFI |
Interface infrarouge IR | 1Interface récepteur infrarouge IR |
Interface ADC | 2Interface ADC |
Interface I2C | 5Interface I2C |
Interface SPI | 2Interface SPI |
POUVEZ | 1Bus CAN |
Ethernet | Une interface RGMII PHY,Gigabit Ethernet |
Mise à niveau du système | Prise en charge de la mise à niveau USB locale |
position du pied | nom/fonction par défaut | Tension E/S | Configurable
Etat |
D'autres fonctions peuvent être réutilisées |
1 | SPKP_OUT | production | La sortie du haut-parleur est positive | |
2 | SPKN_OUT | production | Sortie haut-parleur négative | |
3 | GND | 0V | terrain | |
4 | MIC1_IN | Entrer | entrée micro négative | |
5 | MIC1_INP | Entrer | entrée micro positive | |
6 | HPR_OUT | production | sortie casque droite | |
7 | HP_SNS | HP_SNS | ||
8 | HPL_OUT | production | sortie casque gauche | |
9 | KEY_RESET | IO=1V8 | Entrer | Bouton de réinitialisation La résistance pull-up externe n'est pas autorisée |
10 | KEY_PWR | E/S=5V | Entrer | Allumer et éteindre le clavier Les résistances pull-up externes ne sont pas autorisées |
11 | CLK_32K | IO=1V8 | production | CLK_32K |
12 | VDC | IO=3V3 | Entrer | Bouton de démarrage automatique de haut niveau pour démarrer |
13 | EMMC_KEY | Entrer | clé de mise à niveau | |
14 | ADKEY_IN0 | IO=1V8 | Entrer | ADKEY_IN0 |
15 | ADKEY_IN1 | IO=1V8 | Entrer | ADKEY_IN1 |
16 | VCC_1V8 | 1V8 | production | SORTIE D'ALIMENTATION LDO4 1V8 |
17 | VCC_3V3 | 3V3 | production | VCC8 SORTIE ALIMENTATION 3V3 |
18 | VCC3V3_SYS | 3V3 | production | BUCK4 SORTIE D'ALIMENTATION 3V3 |
19 | GMAC_CLK_M0 | IO=1V8/3V3 | Entrer | CIF_D12_M0/RGMII_CLK_M0/PDM_CLk0_M1
/SPI1_CLK_M0/GPIO3_C0_d |
20 | CLK_25M_ETHERNET | IO=1V8/3V3 | Entrer | CIF_CLKIN_M0/CLK_OUT_ETHERNET_M0
/UART3_CTSN_M0/GPIO3_C5_d |
21 | GMAC_RXCLK_M0 | IO=1V8/3V3 | Entrer | CIF_HSYNC_M0/RGMII_RXCLK_M0/UART3_RX_M0
/GPIO3_C7_d |
22 | GMAC_RXDV_M0 | IO=1V8/3V3 | Entrer | CIF_D13_M0/RGMII_RXDV_M0/PDM_SDI0_M1
/GPIO3_C1_d |
23 | GMAC_RXD0_M0 | IO=1V8/3V3 | Entrer | CIF_D10_M0/RGMII_RXD0_M0/PDM_SDI2_M1
/SPI1_MOSI_M0/GPIO3_B6_d |
24 | GMAC_RXD1_M0 | IO=1V8/3V3 | Entrer | CIF_D11_M0/RGMII_RXD1_M0/PDM_SDI3_M1
/SPI1_MISO_M0/GPIO3_B7_d |
25 | GMAC_RXD2_M0 | IO=1V8/3V3 | Entrer | CIF_D3_M0/RGMII_RXD2_M0/I2S0_SDI0_M1
/UART5_RX_M0/CAN_TXD_M1/PWM11_IR_M0 /GPIO3_A7_d |
26 | GMAC_RXD3_M0 | IO=1V8/3V3 | Entrer | CIF_D4_M0/RGMII_RXD3_M0/I2S0_MCLK_M1
/UART5_RTSN_M0/I2C5_SCL_M1/GPIO3_B0_d |
27 | GMAC_TXCLK_M0 | IO=1V8/3V3 | production | CIF_CLKOUT_M0/RGMII_TXCLK_M0/UART3_TX_M0
/GPIO3_C6_d |
28 | GMAC_TXEN_M0 | IO=1V8/3V3 | production | CIF_D9_M0/RGMII_TXEN_M0/I2S0_SDO3_SDI1_M1
/SPI1_CS0n_M0/GPIO3_B5_d |
29 | GMAC_TXD0_M0 | IO=1V8/3V3 | production | CIF_D7_M0/RGMII_TXD0_M0/I2S0_SDO1_SDI3_M1
UART4_CTSN_M0/GPIO3_B3_d |
30 | GMAC_TXD1_M0 | IO=1V8/3V3 | production | CIF_D8_M0/RGMII_TXD1_M0/I2S0_SDO2_SDI2_M1
/SPI1_CS1n_M0/GPIO3_B4_d |
31 | GMAC_TXD2_M0 | IO=1V8/3V3 | production | CIF_D5_M0/RGMII_TXD2_M0/I2S0_SCLK_RX_M1
/UART5_CTSN_M0/I2C5_SDA_M1/GPIO3_B1_d |
32 | GMAC_TXD3_M0 | IO=1V8/3V3 | production | CIF_D6_M0/RGMII_TXD3_M0/I2S0_LRCK_RX_M1
/UART4_RTSN_M0/GPIO3_B2_d |
33 | GMAC_MDIO_M0 | IO=1V8/3V3 | entrée sortie | CIF_D15_M0/RGMII_MDIO_M0/PDM_CLk1_M1
/GPIO3_C3_d |
34 | GMAC_MDC_M0 | IO=1V8/3V3 | production | CIF_VSYNC_M0/RGMII_MDC_M0/UART3_RTSN_M0
/GPIO3_C4_d |
35 | GPIO3_A4 | IO=1V8/3V3 | entrée sortie | CIF_D0_M0/I2S0_SCLK_TX_M1/UART4_TX_M0
/I2C3_SCL_M0 PWM8_M0/GPIO3_A4_d |
36 | GPIO3_A5 | IO=1V8/3V3 | entrée sortie | CIF_D1_M0/RGMII_CRS_M0/I2S0_LRCK_TX_M1
/UART4_RX_M0/I2C3_SDA_M0/PWM9_M0/GPIO3_A5_d |
37 | GPIO3_A6 | IO=1V8/3V3 | entrée sortie | CIF_D2_M0/RGMII_COL_M0/I2S0_SDO0_M1
/UART5_TX_M0/CAN_RXD_M1/PWM10_M0/GPIO3_A6_d |
38 | GPIO3_C2 | IO=1V8/3V3 | entrée sortie | CIF_D14_M0/RGMII_RXER_M0/PDM_SDI1_M1/GPIO3_C2_d |
39 | VCCIO6_VDD | 1V8/3V3 | Entrer | L'entrée d'alimentation VCCIO6 IO par défaut 1,8 V peut être changée en 3,3 V |
40 | GND | 0V | terrain | |
41 | SDA3 | IO=3V3 | entrée sortie | I2C3_SDA_M1/PWM10_M1/SPI1_CLK_M2/LCDC_HSYNC
/GPIO2_D5_d |
42 | SCL3 | IO=3V3 | production | I2C3_SCL_M1/PWM6_M1/SPI1_CS0n_M2/LCDC_DEN
/GPIO2_D4_d |
43 | PWM9 | IO=3V3 | entrée sortie | UART3_RTSN/M2 PWM9_M1/SPI1_MOSI_M2
/LCDC_VSYNC GPIO2_D6_d |
44 | PWM8 | IO=3V3 | entrée sortie | UART3_CTSN/M2 PWM8_M1/SPI1_MISO_M2
/LCDC_CLK/GPIO2_D7_d |
45 | UART2_TX | IO=3V3 | production | A7_JTAG_TCK_M1/UART2_TX_M1/GPIO3_A2_u |
46 | UART2_RX | IO=3V3 | Entrer | A7_JTAG_TMS_M1/UART2_RX_M1/GPIO3_A3_u |
47 | UART3_TX | IO=3V3 | production | I2C4_SCL_M0/CAN_RXD_M0/UART3_TX_M2
/PWM7_IR_M1/SPI1_CS1n_M2/GPIO3_A0_u |
48 | UART3_RX | IO=3V3 | Entrer | I2C4_SDA_M0/CAN_TXD_M0/UART3_RX_M2
/PWM11_IR_M1/GPIO3_A1_u |
49 | UART4_TX | IO=3V3 | production | UART4_TX_M1/PWM5_M1/RGMII_COL_M1
/CIF_D2_M1/LCDC_D2/GPIO2_A6_d |
50 | UART4_RX | IO=3V3 | Entrer | I2S2_SDO_M1/UART4_RX_M1/PWM4_M1
/SPI0_CS0n_M2/LCDC_D3/GPIO2_A7_d |
51 | UART5_TX | IO=3V3 | production | I2S2_SDI_M1/UART5_TX_M1/PWM3_IR_M1
/SPI0_MOSI_M2/LCDC_D4/GPIO2_B0_d |
52 | UART5_RX | IO=3V3 | Entrer | I2S2_SCLK_M1/UART5_RX_M1/PWM2_M1
/SPI0_MISO_M2/LCDC_D5/GPIO2_B1_d |
53 | GPIO2_B5 | IO=3V3 | Entrer | RGMII_RXD0_M1/CIF_D5_M1/LCDC_D9/GPIO2_B5_d |
54 | GPIO2_B6 | IO=3V3 | entrée sortie | RGMII_RXD1_M1/CIF_D6_M1/LCDC_D10/GPIO2_B6_d |
55 | GPIO2_B7 | IO=3V3 | entrée sortie | RGMII_CLK_M1/CIF_D7_M1/LCDC_D11/GPIO2_B7_d |
56 | GPIO2_C3 | IO=3V3 | entrée sortie | RGMII_TXD0_M1/CIF_D11_M1/LCDC_D15/GPIO2_C3_d |
57 | GPIO2_C4 | IO=3V3 | entrée sortie | RGMII_TXD1_M1/CIF_D12_M1/LCDC_D16/GPIO2_C4_d |
58 | GPIO2_C6 | IO=3V3 | entrée sortie | RGMII_TXEN_M1/CIF_D14_M1/LCDC_D18/GPIO2_C6_d |
59 | GPIO2_A5 | IO=3V3 | entrée sortie | I2C5_SCL_M0/UART4_CTSN_M1/RGMII_CRS_M1
/CIF_D1_M1/LCDC_D1/GPIO2_A5_d |
60 | GPIO2_C2 | IO=3V3 | entrée sortie | RGMII_MDC_M1/CIF_D10_M1/LCDC_D14/GPIO2_C2_d |
61 | GPIO2_C1 | IO=3V3 | entrée sortie | RGMII_MDIO_M1/CIF_D9_M1/LCDC_D13/GPIO2_C1_d |
62 | GPIO2_B4 | IO=3V3 | entrée sortie | RGMII_RXDV_M1/CIF_D4_M1/LCDC_D8/GPIO2_B4_d |
63 | GPIO2_C0 | IO=3V3 | entrée sortie | RGMII_RXER_M1/CIF_D8_M1/LCDC_D12/GPIO2_C0_d |
64 | GPIO2_D3 | IO=3V3 | entrée sortie | I2S1_SDI_M2/RGMII_RXCLK_M1/CIF_HSYNC_M1
/LCDC_D23/GPIO2_D3_d |
65 | GPIO2_D1 | IO=3V3 | entrée sortie | I2S1_SCLK_M2/RGMII_TXD2_M1/CIF_CLKOUT_M1
/LCDC_D21/GPIO2_D1_d |
66 | GPIO2_D2 | IO=3V3 | entrée sortie | I2S1_LRCK_M2/RGMII_TXCLK_M1/CIF_CLKIN_M1
/LCDC_D22/GPIO2_D2_d |
67 | ICR_BIN | IO=3V3 | entrée sortie | I2S1_SDO_M2/RGMII_RXD3_M1/CIF_VSYNC_M1
/LCDC_D20/GPIO2_D0_d |
68 | GPIO2_C7 | IO=3V3 | entrée sortie | I2S1_MCLK_M2/RGMII_RXD2_M1/CIF_D15_M1
/LCDC_D19/GPIO2_C7_d |
69 | GPIO2_C5 | IO=3V3 | entrée sortie | CLK_OUT_ETHERNET_M1/CIF_D13_M1/LCDC_D17
/GPIO2_C5_d |
70 | PWM0 | IO=3V3 | entrée sortie | I2C5_SDA_M0/I2S2_MCLK_M1/UART5_CTSN_M1
/PWM0_M1/SPI0_CS1n_M2/CIF_D3_M1/LCDC_D7/GPIO2_B3_d |
71 | PWM1 | IO=3V3 | entrée sortie | I2S2_LRCK_M1/UART5_RTSN_M1/PWM1_M1
/SPI0_CLK_M2/LCDC_D6/GPIO2_B2_d |
72 | ICR_AIN | IO=3V3 | entrée sortie | UART4_RTSN_M1/RGMII_TXD3_M1/CIF_D0_M1
/LCDC_D0/GPIO2_A4_d |
73 | MIPI_DSI_TX0_CLKN | production | MIPI_DSI_TX0_CLKN | |
74 | MIPI_DSI_TX0_CLKP | production | MIPI_DSI_TX0_CLKP | |
75 | MIPI_DSI_TX0_D0N | production | MIPI_DSI_TX0_D0N | |
76 | MIPI_DSI_TX0_D0P | production | MIPI_DSI_TX0_D0P | |
77 | MIPI_DSI_TX0_D1N | production | MIPI_DSI_TX0_D1N | |
78 | MIPI_DSI_TX0_D1P | production | MIPI_DSI_TX0_D1P | |
79 | MIPI_DSI_TX0_D2N | production | MIPI_DSI_TX0_D2N | |
80 | MIPI_DSI_TX0_D2P | production | MIPI_DSI_TX0_D2P | |
81 | MIPI_DSI_TX0_D3N | production | MIPI_DSI_TX0_D3N | |
82 | MIPI_DSI_TX0_D3P | production | MIPI_DSI_TX0_D3P | |
83 | UART0_RTSN | IO=1V8 | Entrer | UART0_RTSn/GPIO1_C0_u |
84 | UART0_TX | IO=1V8 | production | UART0_TX/GPIO1_C3_u |
85 | UART0_RX | IO=1V8 | Entrer | UART0_RX/GPIO1_C2_u |
86 | UART0_CTSN | IO=1V8 | production | UART0_CTSn/GPIO1_C1_u |
87 | PCM_SYNC | IO=1V8 | production | I2S2_LRCK_M0/SPI1_CS0n_M1
/UART1_CTSn_M1 GPIO1_C7_d |
88 | PCM_TX | IO=1V8 | production | I2S2_SDO_M0/SPI1_MOSI_M1
/FLASH_TRIG_OUT/GPIO1_C4_d |
89 | PCM_CLK | IO=1V8 | production | I2S2_SCLK_M0/SPI1_CLK_M1
/PRELIGHT_TRIG_OUT/UART1_RTSn_M1 GPIO1_C6_d |
90 | PCM_RX | IO=1V8 | Entrer | I2S2_SDI_M0/SPI1_MISO_M1/FLASH_TRIG_IN/GPIO1_C5_d |
91 | VCCIO3 | 1V8/3V3 | Entrer | Entrée d'alimentation VCCIO3 IO = 1V8/3V3 |
92 | SDIO_D1 | IO=1V8 | entrée sortie | SDIO_D1/GPIO1_B5_u |
93 | SDIO_D0 | IO=1V8 | entrée sortie | SDIO_D0/GPIO1_B4_u |
94 | SDIO_CLK | IO=1V8 | production | SDIO_CLK/GPIO1_B2_d |
95 | GND | 0V | terrain | |
96 | SDIO_CMD | IO=1V8 | production | SDIO_CMD/GPIO1_B3_u |
97 | SDIO_D3 | IO=1V8 | entrée sortie | SDIO_D3/GPIO1_B7_u |
98 | SDIO_D2 | IO=1V8 | entrée sortie | SDIO_D2/GPIO1_B6 |
99 | MIPI_CSI_RST0 | IO=1V8 | production | I2S2_MCLK_M0/SPI1_CS1n_M1/SDIO_DET
/I2C5_SCL_M2/UART1_TX_M1/GPIO1_D0_d |
100 | MIPI_CSI_RST1 | IO=1V8 | production | SDIO_PWR/I2C5_SDA_M2/UART1_RX_M1/GPIO1_D1_d |
101 | I2C2_SDA | IO=3V3 | entrée sortie | I2C2_SDA/PWM5_M0/GPIO0_C3_d |
102 | I2C2_SCL | IO=3V3 | production | I2C2_SCL/PWM4_M0/GPIO0_C2_d |
103 | USB_CTRL | IO=3V3 | production | USB_CTRL/PMU_DEBUG/UART1_CTSN_M0
/PWM3_IR_M0/GPIO0_C1_d |
104 | GPIO0_C0 | IO=3V3 | Entrer | SDMMC0_PWR/UART1_RTSN_M0/PWM2_M0/GPIO0_C0_d |
105 | UART1_RX | IO=3V3 | Entrer | UART1_RX_M0/PWM1_M0/GPIO0_B7_d |
106 | UART1_TX | IO=3V3 | production | UART1_TX_M0/PWM0_M0/GPIO0_B6_d |
107 | GPIO0_B3 | IO=3V3 | entrée sortie | FLASH_VOL_SEL |
108 | GPIO4_A1 | IO=1V8 | entrée sortie | I2S0_SDO3_SDI1_M0/PDM_SDI1_M0/I2C4_SDA_M1
/AUDPWM_R_M0/AUDDSM_RP/GPIO4_A1_d |
109 | MIPI_CSI_PWDN1 | IO=1V8 | production | I2S0_SDO2_SDI2_M0/PDM_SDI2_M0/I2C4_SCL_M1
/AUDPWM_L_M0/AUDDSM_RN/GPIO4_A0_d |
110 | PDM_SDI0 | IO=1V8 | Entrer | I2S0_SDI0_M0/PDM_SDI0_M0/ACODEC_DAC_DATAL
/GPIO3_D6_d |
111 | PDM_CLK | IO=1V8 | production | I2S0_LRCK_RX_M0/PDM_CLk0_M0/ACODEC_ADC_SYNC
/GPIO3_D4_d |
112 | WIFI_WAKE_HOST | IO=1V8 | Entrer | SPI0_CLK_M0/GPIO0_B0_d |
113 | BT_RST | IO=1V8 | production | SPI0_MISO_M0/GPIO0_A7_d |
114 | WIFI_REG_ON | IO=1V8 | production | SPI0_MOSI_M0/GPIO0_A6_d |
115 | GPIO0_A5 | IO=1V8 | entrée sortie | SPI0_CS0n_M0/GPIO0_A5_u |
116 | GPIO0_A5 | IO=1V8 | entrée sortie | SPI0_CS1n_M0/GPIO0_A4_u |
117 | SDMMC0_DET | IO=1V8 | Entrer | SDMMC0_DET/GPIO0_A3_u |
118 | GPIO0_A2 | IO=1V8 | entrée sortie | CLKI_CLKO_32K/GPIO0_A2_z |
119 | GPIO0_A0 | IO=1V8 | entrée sortie | CLK_REF/GPIO0_A0_d |
120 | GND | 0V | terrain | |
121 | USB_HOST_DM | entrée sortie | USB_HOST_DM | |
122 | USB_HOST_DP | entrée sortie | USB_HOST_DP | |
123 | OTG_DET_1V8 | IO=1V8 | Entrer | OTG_DET_1V8 |
124 | OTG_ID | IO=1V8 | Entrer | OTG_ID |
125 | OTG_DM | entrée sortie | OTG_DM | |
126 | OTG_DP | entrée sortie | OTG_DP | |
127 | SDMMC0_D1 | IO=3V3 | entrée sortie | UART2_TX_M0/TEST_CLK0_OUT/MCU_JTAG_TRSTn
/SDMMC0_D1/GPIO1_A5_u |
128 | SDMMC0_D0 | IO=3V3 | entrée sortie | UART2_RX_M0/TEST_CLK1_OUT/SDMMC0_D0/GPIO1_A4_u |
129 | SDMMC0_CLK | IO=3V3 | production | UART3_RTSN_M1/MCU_JTAG_TDO/SDMMC0_CLK/GPIO1_B0_u |
130 | GND | 0V | terrain | |
131 | VCC3V3_SD | 3V3 | production | LDO9 SORTIE ALIMENTATION 3V3 |
132 | SDMMC0_CMD | IO=3V3 | production | UART3_CTSN_M1/MCU_JTAG_TDI/SDMMC0_CMD
/GPIO1_B1_u |
133 | SDMMC0_D3 | IO=3V3 | entrée sortie | UART3_TX_M1/A7_JTAG_TMS_M0/MCU_JTAG_TMS/SDMMC0_D3
/GPIO1_A7_u |
134 | SDMMC0_D2 | IO=3V3 | entrée sortie | UART3_RX_M1/A7_JTAG_TCK_M0/MCU_JTAG_TCK
/SDMMC0_D2/GPIO1_A6_u |
135 | VCCIO4 | 1V8/3V3 | Entrer | Entrée d'alimentation VCCIO4 IO = 1V8/3V3 |
136 | I2C1_SCL | IO=1V8/3V3 | production | I2C1_SCL/UART4_CTSN_M2/GPIO1_D3_u |
137 | I2C1_SDA | IO=1V8/3V3 | entrée sortie | I2C1_SDA/UART4/RTSN_M2/GPIO1_D2_u |
138 | SPI0_CLK_M1 | IO=1V8/3V3 | production | SPI0_CLK_M1/I2S1_SDO_M1/UART5_RX_M2/GPIO2_A1_d |
139 | SPI0_MISO_M1 | IO=1V8/3V3 | Entrer | SPI0_MISO_M1/I2S1_LRCK_M1/I2C3_SDA_M2/GPIO1_D7_d |
140 | SPI0_MOSI_M1 | IO=1V8/3V3 | production | SPI0_MOSI_M1/I2S1_SCLK_M1/I2C3_SCL_M2/GPIO1_D6_d |
141 | SPI0_CS0n_M1 | IO=1V8/3V3 | production | SPI0_CS0n_M1/I2S1_SDI_M1/UART5_TX_M2/GPIO2_A0_d |
142 | SPI0_CS1n_M1 | IO=1V8/3V3 | production | SPI0_CS1n_M1/I2S1_MCLK_M1/UART4_TX_M2/GPIO1_D5_d |
143 | MIPI_CSI_PWDN0 | IO=1V8/3V3 | production | UART4_RX_M2/GPIO1_D4_d |
144 | MIPI_CSI_CLK0 | IO=1V8/3V3 | production | MIPI_CSI_CLK0 / UART5_CTSN / M2 / GPIO2_A3_d |
145 | GND | 0V | terrain | |
146 | MIPI_CSI_RX0_CLKN | Entrer | MIPI_CSI_RX0_CLKN | |
147 | MIPI_CSI_RX0_CLKP | Entrer | MIPI_CSI_RX0_CLKP | |
148 | MIPI_CSI_RX0_D3N | Entrer | MIPI_CSI_RX0_D3N | |
149 | MIPI_CSI_RX0_D3P | Entrer | MIPI_CSI_RX0_D3P | |
150 | MIPI_CSI_RX0_D2N | Entrer | MIPI_CSI_RX0_D2N | |
151 | MIPI_CSI_RX0_D2P | Entrer | MIPI_CSI_RX0_D2P | |
152 | MIPI_CSI_RX0_D1N | Entrer | MIPI_CSI_RX0_D1N | |
153 | MIPI_CSI_RX0_D1P | Entrer | MIPI_CSI_RX0_D1P | |
154 | MIPI_CSI_RX0_D0N | Entrer | MIPI_CSI_RX0_D0N | |
155 | MIPI_CSI_RX0_D0P | Entrer | MIPI_CSI_RX0_D0P | |
156 | MIPI_CSI_CLK1 | IO=1V8/3V3 | production | MIPI_CSI_CLK1/UART5_RTSN_M2/GPIO2_A2_d |
157 | MIPI_CSI_RX1_CLKN | Entrer | MIPI_CSI_RX1_CLKN | |
158 | MIPI_CSI_RX1_CLKP | Entrer | MIPI_CSI_RX1_CLKP | |
159 | MIPI_CSI_RX1_D3N | Entrer | MIPI_CSI_RX1_D3N | |
160 | MIPI_CSI_RX1_D3P | Entrer | MIPI_CSI_RX1_D3P | |
161 | MIPI_CSI_RX1_D2N | Entrer | MIPI_CSI_RX1_D2N | |
162 | MIPI_CSI_RX1_D2P | Entrer | MIPI_CSI_RX1_D2P | |
163 | MIPI_CSI_RX1_D1N | Entrer | MIPI_CSI_RX1_D1N | |
164 | MIPI_CSI_RX1_D1P | Entrer | MIPI_CSI_RX1_D1P | |
165 | MIPI_CSI_RX1_D0N | Entrer | MIPI_CSI_RX1_D0N | |
166 | MIPI_CSI_RX1_D0P | Entrer | MIPI_CSI_RX1_D0P | |
167 | GND | 0V | terrain | |
168 | VCC5V0_SYS | 4.5~5.5V | Entrer | Entrée d'alimentation secteur |
étiquette | position du pied | définition | État actuel des E/S | Tension E/S | fonction un | fonction deux |
6 | BROCHE 1 | PW_FR | production | 5V | Mise sous tension par défaut,
Court-circuit hors tension de la carte mère |
|
BROCHE 2 | GND | terrain | 3V3 |
étiquette | position du pied | définition | État actuel des E/S | Tension E/S | fonction un | fonction deux |
8 | BROCHE 1 | IO2_B7 | entrée sortie | 3V3 | GPIO disponible | |
BROCHE 2 | IO2_C3 | entrée sortie | 3V3 | GPIO disponible | ||
BROCHE 3 | IO2_C4 | entrée sortie | 3V3 | GPIO disponible | ||
BROCHE 4 | IO2_C6 | entrée sortie | 3V3 | GPIO disponible |
étiquette | position du pied | définition | État actuel des E/S | Tension E/S | fonction un | fonction deux |
9 | BROCHE 1 | VDD | terrain | 3V3/5V | Fonction TTL port série 1 (Peut ajouter une puce RS232) |
|
BROCHE 2 | TX | production | 3V3 | GPIO | ||
BROCHE 3 | RX | Entrer | 3V3 | GPIO | ||
BROCHE 4 | GND | terrain | 0V |
étiquette | position du pied | définition | État actuel des E/S | Tension E/S | fonction un | fonction deux |
10 | BROCHE 1 | VDD | terrain | 3V3/5V | Fonction TTL port série 5 (Peut ajouter une puce RS232) |
|
BROCHE 2 | TX | production | 3V3 | GPIO | ||
BROCHE 3 | RX | Entrer | 3V3 | GPIO | ||
BROCHE 4 | GND | terrain | 0V |
étiquette | position du pied | définition | État actuel des E/S | Tension E/S | fonction un | fonction deux |
11 | BROCHE 1 | GND | terrain | 0V | Déboguer le port série 2 | Fonction port série 2 |
BROCHE 2 | TX | production | 3V3 | |||
BROCHE 3 | RX | Entrer | 3V3 |
étiquette | position du pied | définition | État actuel des E/S | Tension E/S | fonction un | fonction deux |
12 | BROCHE 1 | 5V | production | 5V | EMPLACEMENT USB | |
BROCHE 2 | DN | entrée sortie | 3V3 | |||
BROCHE 3 | DP | entrée sortie | 3V3 | |||
BROCHE 4 | GND | terrain | 0V |
étiquette | position du pied | définition | État actuel des E/S | Tension E/S | fonction un | fonction deux |
13 | BROCHE 1 | IO2_C2 | entrée sortie | 3V3 | GPIO disponible | |
BROCHE 2 | IO2_C1 | entrée sortie | 3V3 | GPIO disponible | ||
BROCHE 3 | IO2_B4 | entrée sortie | 3V3 | GPIO disponible | ||
BROCHE 4 | ADC1 | Entrer | 1V8 | Entrée analogique ADC |
étiquette | position du pied | définition | État actuel des E/S | Tension E/S | fonction un | fonction deux |
15 | BROCHE 1 | VDD | terrain | 3V3/5V | Fonction TTL port série 3 (Peut ajouter une puce RS232) |
|
BROCHE 2 | TX | production | 3V3 | GPIO | ||
BROCHE 3 | RX | Entrer | 3V3 | GPIO | ||
BROCHE 4 | GND | terrain | 0V |
étiquette | position du pied | définition | État actuel des E/S | Tension E/S | fonction un | fonction deux |
16 | BROCHE 1 | VDD | terrain | 3V3/5V | Fonction TTL port série 4 (Peut ajouter une puce RS232) |
|
BROCHE 2 | TX | production | 3V3 | GPIO | ||
BROCHE 3 | RX | Entrer | 3V3 | GPIO | ||
BROCHE 4 | GND | terrain | 0V |
étiquette | position du pied | définition | État actuel des E/S | Tension E/S | fonction un | fonction deux |
17 | BROCHE 1 | LVOP | production | 5V | 5Port haut-parleur W | |
BROCHE 2 | LVON | production | 5V | |||
BROCHE 3 | RVOP | production | 5V | |||
BROCHE 4 | RVON | production | 5V |
étiquette | position du pied | définition | État actuel des E/S | Tension E/S | fonction un | fonction deux |
19 | BROCHE 1 | RST | Entrer | 3V3 | Bouton de réinitialisation | |
BROCHE 2 | REP | Entrer | 3V3 | Bouton d'arrêt | ||
BROCHE 3 | SALLE DES MASQUES | Entrer | 3V3 | Clé flash | ||
BROCHE 4 | GND | terrain | 0V | terrain |
étiquette | position du pied | définition | État actuel des E/S | Tension E/S | fonction un | fonction deux |
20 | BROCHE 1 | GND | terrain | 0V | entrée caméra Double MIPI CSI |
|
BROCHE 2 | RX1_D0P | Entrer | ||||
BROCHE 3 | RX1_D0N | Entrer | ||||
BROCHE 4 | RX1_D1P | Entrer | ||||
BROCHE 5 | RX1_D1N | Entrer | ||||
BROCHE 6 | RX1_D2P | Entrer | ||||
BROCHE 7 | RX1_D2N | Entrer | ||||
BROCHE 8 | RX1_D3P | Entrer | ||||
BROCHE 9 | RX1_D3N | Entrer | ||||
BROCHE 10 | GND | terrain | 0V | |||
BROCHE 11 | RX1_CLKP | Entrer | ||||
BROCHE 12 | RX1_CLKN | Entrer | ||||
BROCHE 13 | GND | terrain | 0V | |||
BROCHE 14 | MCLK1 | production | 1V8 | |||
BROCHE 15 | PD1 | production | 1V8 | |||
BROCHE 16 | RST1 | production | 1V8 | |||
BROCHE 17 | GND | terrain | 0V | |||
BROCHE 18 | RX0_D0P | Entrer | ||||
BROCHE 19 | RX0_D0N | Entrer | ||||
BROCHE 20 | RX0_D1P | Entrer | ||||
BROCHE 21 | RX0_D1N | Entrer | ||||
BROCHE 22 | RX0_D2P | Entrer | ||||
BROCHE 23 | RX0_D2N | Entrer | ||||
BROCHE 24 | RX0_D3P | Entrer | ||||
BROCHE 25 | RX0_D3N | Entrer | ||||
BROCHE 26 | GND | terrain | 0V | |||
BROCHE 27 | RX0_CLKP | Entrer | ||||
BROCHE 28 | RX0_CLKN | Entrer | ||||
BROCHE 29 | GND | terrain | 0V | |||
BROCHE 30 | MCLK0 | production | 1V8 | |||
BROCHE 31 | PD0 | production | 1V8 | |||
BROCHE 32 | RST0 | production | 1V8 | |||
BROCHE 33 | SPI0_CS1 | entrée sortie | 1V8 | |||
BROCHE 34 | SPI0_CS0 | entrée sortie | 1V8 | |||
BROCHE 35 | SPI0_MOSI | entrée sortie | 1V8 | |||
BROCHE 36 | SPI0_MISO | entrée sortie | 1V8 | |||
BROCHE 37 | SPI0_CLK | entrée sortie | 1V8 | |||
BROCHE 38 | SDA1 | entrée sortie | 1V8 | |||
BROCHE 39 | SCL1 | production | 1V8 | |||
BROCHE 40 | ICR_AIN | entrée sortie | 1V8 | |||
BROCHE 41 | ICR_BIN | entrée sortie | 1V8 | |||
BROCHE 42 | GND | terrain | 0V | |||
BROCHE 43 | GND | terrain | 0V | |||
BROCHE 44 | 3V3 | production | 3V3 | |||
BROCHE 45 | 3V3 | production | 3V3 | |||
BROCHE 46 | GND | terrain | 0V | |||
BROCHE 47 | 5V | production | 5V | |||
BROCHE 48 | 5V | production | 5V | |||
BROCHE 49 | GND | terrain | 0V | |||
BROCHE 50 | GND | terrain | 0V |
étiquette | position du pied | définition | État actuel des E/S | Tension E/S | fonction un | fonction deux |
22 | BROCHE 1 | VDD | Entrer | 3V | Batterie RTC | |
BROCHE 2 | GND | GND | GND |
étiquette | position du pied | définition | État actuel des E/S | Tension E/S | fonction un | fonction deux |
23 | BROCHE 1 | PWM1 | entrée sortie | 3V | GPIO configurable | |
BROCHE 2 | PWM8 | entrée sortie | 3V3 | GPIO configurable | ||
BROCHE 3 | PWM9 | entrée sortie | 3V3 | GPIO configurable | ||
BROCHE 4 | IO3_C2 | entrée sortie | 3V3 | GPIO configurable | ||
BROCHE 5 | IO0_B3 | entrée sortie | 3V3 | GPIO configurable | ||
BROCHE 6 | GND | terrain | 0V | terrain | ||
BROCHE 7 | 3V3 | production | 3V3 | 3.3Puissance de sortie V |
étiquette | position du pied | définition | État actuel des E/S | Tension E/S | fonction un | fonction deux |
26 | BROCHE 1 | 12V | production | 12V | Interface MIPI+TOUCH | |
BROCHE 2 | GND | terrain | 0V | |||
BROCHE 3 | 5V | production | 5V | |||
BROCHE 4 | GND | terrain | 0V | |||
BROCHE 5 | 3V3 | production | 3V3 | |||
BROCHE 6 | LCD FR | production | 3V3 | |||
BROCHE 7 | TP RST | production | 3V3 | |||
BROCHE 8 | TP INT | Entrer | 3V3 | |||
BROCHE 9 | TP VDD | production | 3V3 | |||
BROCHE 10 | GND | terrain | 0V | |||
BROCHE 11 | TP SCL | production | 3V3 | |||
BROCHE 12 | TP SDA | entrée sortie | 3V3 | |||
BROCHE 13 | GND | terrain | 0V | |||
BROCHE 14 | PWM | production | 3V3 | |||
BROCHE 15 | RST ACL | production | 3V3 | |||
BROCHE 16 | GND | terrain | 0V | |||
BROCHE 17 | CLKM | production | ||||
BROCHE 18 | CLKP | production | ||||
BROCHE 19 | GND | terrain | 0V | |||
BROCHE 20 | 0M | production | ||||
BROCHE 21 | 0P | production | ||||
BROCHE 22 | GND | terrain | 0V | |||
BROCHE 23 | 1M | production | ||||
BROCHE 24 | 1P | production | ||||
BROCHE 25 | GND | terrain | 0V | |||
BROCHE 26 | 2M | production | ||||
BROCHE 27 | 2P | production | ||||
BROCHE 28 | GND | terrain | 0V | |||
BROCHE 29 | 3M | production | ||||
BROCHE 30 | 3P | production |
étiquette | position du pied | définition | État actuel des E/S | Tension E/S | fonction un | fonction deux |
27 | BROCHE 1 | VDD | production | 3V3 | Interface tactile I2C | |
BROCHE 2 | GND | terrain | 0V | |||
BROCHE 3 | RST | production | 3V3 | IO2_D1 | ||
BROCHE 4 | INT | Entrer | 3V3 | IO2_D2 | ||
BROCHE 5 | SCL | production | 3V3 | SCL3 | ||
BROCHE 6 | SDA | entrée sortie | 3V3 | SDA3 |
étiquette | position du pied | définition | État actuel des E/S | Tension E/S | fonction un | fonction deux |
31 | BROCHE 1 | 12V | production | 12V | Infrarouge + lumière blanche,contrôlable | |
BROCHE 2 | GND | terrain | 0V | |||
BROCHE 3 | 5V | production | 5V | |||
BROCHE 4 | GND | terrain | 0V |
Taille | L120mm x L85mm x H14mm |
CPU | Puce suisse RV1109 fréquence double cœur 1200 MHz |
NPU | 1.2 TOPS NPU |
Mémoire | La DDR4 est livrée en standard avec 1G(2Lot G en option) |
Mémoire | eMMC est livré en standard avec 8G(16Lot G/32G/64G en option) |
gestion de l'alimentation | RK809-2 prend en charge la gestion dynamique de l'alimentation |
Tension de fonctionnement | Tension d'entrée 12V puissance maximale inférieure à 5W (Ne connectez aucun périphérique) |
système de support | Linux 4.19 + QT 5.12 |
température de fonctionnement | -10à +60 degrés |
la vie | La durée de vie continue est supérieure à 5 ans |
interface USB | 4USB de route,Port standard A 3 voies(Tout le chemin OTG),En ligne 1 voie |
Port série UART | 5Niveau TTL 3.3V(Peut ajouter une puce RS232),Une façon est le débogage |
Interface PWM | 3Niveau PWM 3.3V |
Interface SDIO | 2Interface SDIO,Tout le chemin carte TF,Une autre façon de se connecter au WIFI |
Interface GPIO | 9GPIO disponible |
Interface ADC | 2Interface ADC |
Interface I2C | 2Interface I2C |
Affichage MIPI DSI | 1路最大1920×1080 60fps |
interface caméra | 2Entrée caméra route mipi csi |
lumière d'appoint | 2Lumière de remplissage contrôlable sur route,1route pour la lumière infrarouge,1la route est blanche |
Entrée vocale | 1Entrée microphone en silicone,Une autre entrée LANE IN |
sortie vocale | 1Sortie des canaux gauche et droit,Amplificateur de puissance 5W fixé à la plaque inférieure |
WIFI | Prend en charge la double bande 2.4G/5G AP6256 |
Bluetooth | Prise en charge de Bluetooth 5.0, prise en charge du mode BLE |
Ethernet | La puce RGMII 100/1000M PHY RTL8211F est connectée par défaut |
4g | Prend en charge l'interface pcie du module Netcom complet 4G |
puissance de sortie | Sortie de puissance multicanal 3.3V 5V 12V |
Mise à niveau du système | Prise en charge de la mise à niveau USB locale |
RTC | Interface pile bouton |