Two-way wireless transmission digital data link module
特征
- COFDM two-way wireless transmission link module
- Wireless pass-through Ethernet ports and 1 wireless pass-through TTL serial port
- Dual antenna transmit and receive, MIMO mode of operation
- Support wireless frequency band: 2401.5~2481.5MHz, 1427.9~1447.9MHz, 806~826MHz, 支持频段内自动跳频
- Wireless bandwidth configurable: 1.4兆赫, 3兆赫, 5兆赫, 10兆赫, 20兆赫, the maximum air interface rate can be matched to 30Mbps
- 调制方法: QPSK/QAM16/QAM64自动适配
- Maximum transmission power: 25±2dBm
- Support wireless link encryption and decryption
- Supports point-to-point and point-to-multipoint communication. 取决于 16 access nodes can be connected to one central node.
灵敏度
频带 | 2.4千兆赫(1Mbps的) | 1.4千兆赫(1Mbps的) | 800兆赫(1mbps) |
20Mhz Bandwidth | -99dBm的 | / | / |
10Mhz Bandwidth | -102dBm的 | -103dBm的 | -103dBm的 |
5Mhz Bandwidth | -104dBm的 | -106dBm的 | -106dBm的 |
3Mhz Bandwidth | -106dBm的 | -108dBm的 | -108dBm的 |
Interface Defines
Ethernet-1: two-way wireless transparent transmission network port, 4PIN 1.25mm pitch with a buckle carrier
Ethernet-2: two-way wireless transparent transmission network port, 4PIN 1.25mm pitch carrier or direct 4PIN soldering hole
Data-UART: bidirectional transparent data serial port, TTL 3.3V电平, 3PIN 1.25mm pitch with a snap carrier
Main Antenna: main antenna interface, IPEX carrier
Second Antenna: Auxiliary antenna interface, IPEX carrier. The auxiliary antenna can only be received. When the DLM module is used for communication, it can be double-received or received.
功率: Power input interface, support 7~24V wide voltage input, maximum power consumption is less than 3.5W.
USB: 4PIN 1.25mm pitch carrier, not yet open to users.
Config UART: 4PIN 1.25mm pitch carrier, not yet open to users.
The DLM module measures 58x48mm (excluding the dimensions of the interface device extending from the edge of the board), the front device height is less than 3.2mm, the back device height is less than 4.5mm, the board thickness is 1.6mm, and the weight is 31.5g.
电源
The power supply signal is shown in the figure above. The power input is 2 solder holes and supports 7~24V wide voltage input. 4V power supply is provided externally for the power supply of the cooling fan.
Ethernet and Data
Signal Indicator
Ethernet-1 LED: 绿色的, a signal indicator on the network port. The network port will flash when transmitting data normally.
Ethernet-2 LED: 绿色的, network port two signal indicator, the network port will flash when transmitting data normally.
Power LED: 红色的, always on when power is normal
Link LED: The working status indicator of the wireless link. When the module works as a slave node, if the wireless connection with the master node is normal, the indicator will be on. This indicator is invalid when the module is working as the master node.
规范
工作频段 | 1428~1448MHz or 802~826MHz |
信道带宽 | 1.4MHz/3MHz/5MHz/10MHz/20MHz |
调制方法 | QPSK/QAM16/QAM64 |
Transmitting power | 300毫瓦, 2w ^, 5w ^ |
组网方式 | 点对点, 点对多点星形网络 |
传输距离 | air-to-ground 15km, 30千米, 50千米, 80千米, 100千米 |
Data interface | 2 网络端口 + 1 serial port |
Wireless transmission rate | maximum 25Mbps, shared by all nodes in two-way transmission. |
天线接口 | 2 SMA connectors |
电源 | 12V or 24V |
尺寸 | 102*52*21.5毫米 (PCBA only) |
重量 | 127 克 |