COFDM Wireless Video Receiver HDMI CVBS output
COFDM Wireless Video Receiver HDMI CVBS output mini modulator module long distance fpv UAV Data Transmission UART config Recorder
کار برای COFDM-905T
HD digital wireless video transmission receiver COFDM-905R
برد داخلی رسیور و ماژول دمودولاسیون دریافت دو آنتن COFDM, کل دستگاه از پوشش آلیاژ آلومینیوم استفاده می کند, حساسیت دریافت بالا, تاخیر کم نمایش رمزگشایی, خروجی ویدیو با کیفیت بالا پایدار و واضح است.
امکانات
- دریافت دو آنتن
- پشتیبانی از محدوده فرکانس کاری: 160MHz~860MHz, فرکانس کاری مرکز را می توان پیکربندی کرد;
- پهنای باند بی سیم قابل تنظیم است;
- حساسیت دریافت آنتن دوگانه -100±1dbm (QPSK 8 مگاهرتز);
- اطلاعات وضعیت دریافت بی سیم (مانند قدرت سیگنال دریافتی, نرخ رابط هوا, نرخ داده, فرکانس کاری, پهنای باند بی سیم, و غیره.) را می توان از طریق دکمه سوئیچ OSD روی صفحه ویدیو روی هم قرار داد/نشان داد, یا خروجی به پورت سریال (سفارشی شده) ;
- رمزگشایی ویدیوی H264 با تاخیر کم, پشتیبانی از پخش رمزگشایی 1080P@60;
- خروجی صدا و تصویر (HDMI, CVBS, خروجی همزمان پورت USB):
- HDMI Type A port audio and video output
- CVBS (سر نیلوفر آبی) خروجی صدا و تصویر AV
- پخش جریانی ویدئو را از طریق درگاه USB به صفحه نمایش رمزگشایی گوشی/تبلت ارسال کنید
- پشتیبانی از عملکرد دریافت و رمزگشایی ویدیو (تطبیق با رمزگذاری ویدئو در انتهای ارسال);
- پشتیبانی از کارت TF یا ضبط ویدئو از دیسک USB;
- ارائه پورت سریال انتقال داده شفاف یک طرفه یک طرفه;
- پارامترهایی را برای پیکربندی پورت سریال برای تنظیمات کار ارائه دهید (مانند فرکانس کاری مرکز, پهنای باند بی سیم, دریافت رمز رمزگشایی);
- منبع تغذیه: 6~ 15 ولت, مصرف برق کاری 230mA@12V است.
- اندازه ماشین: 115x90x34mm
- وزن دستگاه: 243 گرم
اتصال:
- ANT-in: رابط آنتن ورودی سیگنال بی سیم, سوراخ داخلی رزوه ای خارجی SMA
- HDMI: یک نوع حامل HDMI, رابط خروجی صدا و تصویر با کیفیت بالا
- CVBS: رابط خروجی ویدئو آنالوگ
- AL/AR: left and right channel analog audio output
- قدرت اتصال: 3PIN 2.54mm socket
- یو اس بی رابط:
- External phone or tablet can be used to output audio and video to mobile phone or tablet for decoding display
- ضبط فیلم را می توان به یک درایو فلش USB خارجی یا هارد دیسک USB متصل کرد
- OSD button:
The receiving status information displays the on/off button, and the long press button can switch the switch status, and the switch status will be powered off. When the reception status information display is turned on, it is displayed in red in the upper left corner of the output video screen:- RF:338.0MHz BW:4.0مگاهرتز
QPSK CR:2/3 GI:1/16
AIR:3.90مگابیت در ثانیه
VBR:3.05Mbps AES OFF
SIG1:27 SIG2:22
ber1:0.14% ber2:100.00%
REC OFF No Storage - RF indicates the center operating frequency, و BW indicates the working bandwidth.
QPSK is the modulation mode, CR is the convolutional code rate, and GI is the guard interval.
AIR is the air interface rate
VBR is the video bitrate, AES OFF means no encryption
SIG1 refers to the received signal strength near the HDMI port antenna, و SIG2 refers to the other antenna.
Ber1 refers to the BER error rate near the HDMI port antenna, و ber2 refers to another antenna.
REC OFF means no video storage
- RF:338.0MHz BW:4.0مگاهرتز
- When the wireless receiving signal is interrupted or weak, the output video screen will be interrupted (the re-received signal screen will be automatically restored), and display: Disconnected, no signal
- REC button: Video recording on/off button, short press button to switch state, start recording after power is detected. The system defaults to recording to the TF card. If the TF card is not inserted, it is recorded to the USB flash drive. If they are not inserted, they will not be recorded.
- Link indicator: The wireless receiving link working status indicator lights up after the system is started and blinks when the receiving signal is normal.
- REC indicator: The video recording indicator will flash at the low frequency when recording video, otherwise the high frequency will flash.
- PWR indicator: شاخص توان.
- CFG serial port: Parameter configuration Serial port, you can configure wireless receiving related parameters, مانند فرکانس کاری مرکز, پهنای باند بی سیم, decryption password, و غیره. Vcan provides a matching parameter configuration panel SconB to facilitate user parameter setting.
- Data serial port: Transparent data transmission serial port. The serial port data of the transmitter can be wirelessly transmitted to the receiver and output from the serial port.
- TF card interface: Used for software upgrade maintenance or for storing video.
توجه داشته باشید
When the COFDM-905T transmitter and COFDM-905T receiver form a point-to-point wireless video transmission system, the video delay indicator:
The three indicators of video delay, video bit rate, and air interface rate are the mutual influence and mutual restraint. When the air interface rate is greater than 5 times the video code rate, the video delay is minimum. In this case, the actual test is that the video delay is about 60 ms when the code is transmitted at 720P@60, and the video delay is about 130 ms at 1080P@60. The delay refers to the delay from the HDMI video input at the transmitting end to the HDMI video output at the receiving end, excluding the delay of the front-end camera of the transmitting end (we measured the delay of a brand SLR camera at about 70 خانم, and the delay of a famous brand sports camera at about 130 خانم). For most application scenarios, the video delay is set to about 200ms by default.
When the COFDM-905T transmitter and the COFDM-905R receiver form a point-to-point wireless video transmission system, the transmission distance is:
The wireless transmission distance is related to many factors such as the test environment, ambient electromagnetic interference, occlusion conditions, air humidity, فرکانس کاری, پهنای باند بی سیم, and transmitting and receiving antennas. Actual test results: a customer test, unmanned aircraft mounted ST100 transmitter to fly about 100 meters high, set to 4M QPSK wireless bandwidth, 700MHz center operating frequency, 1W transmit power, transmitter antenna 3dBi around, Receiving double glass fiber antenna gain of about 10dBi, distance of up to 16km (video smooth); our own road test in Shenzhen, the launch end on the flyover, ordinary hose antenna (about 3dBi gain), 340MHz launch, QPSK 8M Bandwidth, a fiberglass antenna at the receiving end, and a Yagi antenna, در باره 2.2 meters high on the pole, 2.2 kilometers away, high-definition video smooth, a small amount of high-rise buildings between the transmitter and receiver, the road visually about 20 degrees bending. Due to conditional restrictions, no further road tests were made.
اتصال
اندازه
75 ایکس 55 ایکس 25 میلی متر
تست عملکرد RF
فرکانس مرکز عملیات 470 مگاهرتز, تقویت کننده توان: 1W
فرکانس مرکز عملیات 700 مگاهرتز, تقویت کننده توان: 1W
نقد و بررسیها
هنوز بررسیای ثبت نشده است.