TDD PA Power Amplifier Module for DVB-T COFDM TX Transmitter transmission 1w 2w 5w 10w 15w 20w
TDD pa power amplifier
TDD PA Power Amplifier Module for DVB-T COFDM TX Transmitter transmission 5w
The pa power amplifier module realizes the power amplification output of the RF signal. When the input voltage is 28V, connect to COFDM modulation board, the output power can be up to 5W (+30DBM)
Features
- Working frequency band: 815MHz~830MHz (more frequency is adjustable)
- RX Gain: 1dB+/-1dB
- TX Gain: 10dB+/-1dB
- TX Power: 5W
spesifikaasje
| Ûnderdiel | Parameter | Noat |
| Frekwinsjeberik (MHz) | 815-830Mzh | accept modify according to buyer’s requirement |
| Output power (W) | 5W | No ALC control |
| In-band group delay (ns) | ≤50 | |
| TX gain (dB) | 16±1.0 | Set gain according to customer requirements |
| In-band fluctuation | ≤1dB | Peak |
| ynfier nivo (DBM) | +22±1.0 | |
| Shoulder ratio (dBc) | ≤-30 | |
| RX gain (dB) | 5 | |
| RX Noise figure (dB) | ≤2.5 | |
| RF switching level | +3.3V～+5V | High level send low-level receive |
| Isolation | 50dB | |
| Power supply requirements | +11V～+18V Vdc | |
| RX operating current | ≤0.6A | |
| TX operating current | ≤3.0A | |
| Wurk temperatuer | -20～+70℃ | |
| Interface Type | SMA-50KFD | |
| Module Dimension (mm) | 105 * 60 * 14 |
Shape and installation instructions
1. Ofmjittings: 105 * 60 *14 (mm) (without socket)
2. Interface form:
1 power supply conditions: +12V power supply: plug
2 RF input interface: SMA-50KFD
RF output interface: SMA-50KFD
3. Mounting hole diameter size: 4 Φ3.5 through holes for 4 mounting holes for installation.
20W
spesifikaasje
| Ûnderdiel | Parameter | Noat |
| Frekwinsjeberik (MHz) | 500-530Mzh | accept modify according to buyer’s requirement |
| Output power (W) | 20W | No ALC control |
| In-band group delay (ns) | ≤50 | |
| TX gain (dB) | 48±1.0 | Set gain according to customer requirements |
| In-band fluctuation | ≤1dB | Peak |
| ynfier nivo (DBM) | -80 | |
| Shoulder ratio (dBc) | ≤-30 | |
| RX gain (dB) | 5 | |
| RX Noise figure (dB) | ≤2.5 | |
| RF switching level | +3.3V～+5V | High level send low-level receive |
| Isolation | 50dB | |
| Power supply requirements | ≤＋28 Vdc 20W/3A | |
| RX operating current | ≤0.6A | |
| TX operating current | ≤3.0A | |
| Wurk temperatuer | -20～+65℃ | |
| Interface Type | SMA-50KFD | |
| Module Dimension (mm) | 178 × 91 × 25 |
Power supply conditions:
+28V power supply: Pin 2
+12V power supply: Pin 3
Grounding: Pin 1
Resinsjes
Der binne gjin rapporten.